The Kawasaki ZX600, 636 (ZX-6R) repair manual by Haynes covers:
- 2004 Kawasaki 636 Service Manual
- 2004 Kawasaki Ninja 636 Value
- 2004 Kawasaki 636 Manual Transmission
- Kawasaki 636 For Sale
Anglicky kawasaki zx6rr 2003 2004 service manual.pdf 2003-2004 Anglicky zx600j8f.pdf 2000-2002 ZX6R & 2003-2008 ZZR600 2000-2008 Anglicky kawasaki zx 6r 2005 service manual 2nd edition zx636c1 c6f d6f.pdf 2005. Get the best deals on Engines & Parts for Kawasaki Ninja ZX6R when you shop the largest online selection at eBay.com. Free shipping on many items. 2002 2003 2004, Clutch Kit - NEW - ZX6R, 636 (Fits: Kawasaki Ninja ZX6R) $36.99. $5.99 shipping. Kawasaki ZX6R Ninja 6R Manual Camchain Tensioner by PSR 1996-17 P/N 04-020004-29 (Fits. Research 2004 Kawasaki ZX636B2 Ninja ZX-6R standard equipment and specifications at NADAguides. 636 Engine Type. Manual Number of Speeds.
U.S. models:
- Kawasaki ZX600F, 1995-1997
- Kawasaki ZX600G, 1998-1999
- Kawasaki ZX600H, 1998
- Kawasaki ZX600J, 2000-2002
Download manual guide of 2004 Kawasaki Zx6r 636 Electrical Wiring Diagram in pdf that we categorized in Manual Guide. This manual books file was hosted in www.guhlmotors.com that avaialble for FREE DOWNLOAD as owners manual, user guide / buyer guide or mechanic reference guide. Models Kawasaki ZX-6R 636 (ZX636A) 2002 (Europe, Asia and other) Kawasaki ZX-6R 636 (ZX636B) 2003-2004 (Europe, North America, Asia and other).
U.K. and Europe models![2004 Kawasaki 636 Manual 2004 Kawasaki 636 Manual](https://www.tradebit.com/usr/cathy19890614/pub/9002/175834998_q10.jpg)
- Kawasaki ZX600F, 1995-1997
- Kawasaki ZX600G, 1998-1999
- Kawasaki ZX600H, 1998 (except UK)
- Kawasaki ZX600J, 2000-2001
- Kawasaki ZX636A, 2002
Book Excerpt: 1995-2002 Kawasaki Ninja ZX600, 636 (ZX-6R) Repair Manual
FUEL AND EXHAUST SYSTEMS
GENERAL INFORMATIONThe fuel system consists of the fuel tank, fuel tap, fuel pump, filters, carburetors and the connecting hoses and control cables.
The carburetors used are four constant vacuum Keihin (F models) or Mikuni (G, H, J and A models) with butterfly-type throttle valves. For cold starting, an enrichment circuit is actuated by a cable from the choke lever mounted on the left handlebar.
The exhaust system is a four-into-one design. An open-loop catalytic converter is fitted in the exhaust system of California market G models, H models for Germany and Switzerland, and all J and A models except for the Australian market.
The catalytic converters are protected from the intake of excess unburnt fuel by the carburetor mounted fuel cut-off valves.
Many of the fuel system service procedures are considered routine maintenance items and for that reason are included in Chapter 1.
FUEL TANK AND TAP | REMOVAL, CLEANING, REPAIR, INSTALLATION
WARNING: Refer to the warning in Section 1 concerning contact with fuel.
REMOVAL
- Turn the fuel tap to the OFF position.
- Remove the seats (see Chapter 8).
- On California models, mark and disconnect the evaporative emission hoses.
- On F models, remove the two screws securing the tap to the bracket and detach the tap (see illustration). Release the clamp securing the fuel hose to the union on the side of the fuel tap and detach the hose (see illustration).
- On G, H, J and A models, remove the screw from the center of the fuel tap knob using a small Phillips screwdriver, then detach the knob from the tap (see illustration).Release the clamp securing the fuel hose to the union on the side of the fuel tap and detach the hose (see illustration).
ELECTRICAL SYSTEM
2004 Kawasaki 636 Service Manual
TURN SIGNAL BULBS | REPLACEMENT2004 Kawasaki Ninja 636 Value
- Remove the screw securing the turn signal lens and remove the lens, noting how it fits (see illustration). Remove the rubber gasket if it is free, and discard it if it is damaged or deteriorated.
- Push the bulb into the holder and twist it anti-clockwise to remove it (see illustration). Check the socket terminals for corrosion and clean them if necessary.Line up the pins of the new bulb with the slots in the socket, then push the bulb in and turn it clockwise until it locks into place.
- Fit the lens onto the holder, using a new rubber gasket if required, and make sure it is properly seated and not pinched by the lens.